--- libev/ev.pod 2007/11/24 10:15:16 1.40 +++ libev/ev.pod 2007/11/24 16:33:23 1.43 @@ -470,6 +470,7 @@ =back + =head1 ANATOMY OF A WATCHER A watcher is a structure that you create and register to record your @@ -578,7 +579,7 @@ =back -=head2 SUMMARY OF GENERIC WATCHER FUNCTIONS +=head2 GENERIC WATCHER FUNCTIONS In the following description, C stands for the watcher type, e.g. C for C watchers and C for C watchers. @@ -597,7 +598,7 @@ You can reinitialise a watcher at any time as long as it has been stopped (or never started) and there are no pending events outstanding. -The callbakc is always of type C. =item C (ev_TYPE *, [args]) @@ -693,13 +694,15 @@ information given in the last section. -=head2 C - is this file descriptor readable or writable +=head2 C - is this file descriptor readable or writable? I/O watchers check whether a file descriptor is readable or writable -in each iteration of the event loop (This behaviour is called -level-triggering because you keep receiving events as long as the -condition persists. Remember you can stop the watcher if you don't want to -act on the event and neither want to receive future events). +in each iteration of the event loop, or, more precisely, when reading +would not block the process and writing would at least be able to write +some data. This behaviour is called level-triggering because you keep +receiving events as long as the condition persists. Remember you can stop +the watcher if you don't want to act on the event and neither want to +receive future events. In general you can register as many read and/or write event watchers per fd as you want (as long as you don't confuse yourself). Setting all file @@ -709,33 +712,37 @@ You have to be careful with dup'ed file descriptors, though. Some backends (the linux epoll backend is a notable example) cannot handle dup'ed file descriptors correctly if you register interest in two or more fds pointing -to the same underlying file/socket etc. description (that is, they share +to the same underlying file/socket/etc. description (that is, they share the same underlying "file open"). If you must do this, then force the use of a known-to-be-good backend (at the time of this writing, this includes only C and C). +Another thing you have to watch out for is that it is quite easy to +receive "spurious" readyness notifications, that is your callback might +be called with C but a subsequent C(2) will actually block +because there is no data. Not only are some backends known to create a +lot of those (for example solaris ports), it is very easy to get into +this situation even with a relatively standard program structure. Thus +it is best to always use non-blocking I/O: An extra C(2) returning +C is far preferable to a program hanging until some data arrives. + +If you cannot run the fd in non-blocking mode (for example you should not +play around with an Xlib connection), then you have to seperately re-test +wether a file descriptor is really ready with a known-to-be good interface +such as poll (fortunately in our Xlib example, Xlib already does this on +its own, so its quite safe to use). + =over 4 =item ev_io_init (ev_io *, callback, int fd, int events) =item ev_io_set (ev_io *, int fd, int events) -Configures an C watcher. The fd is the file descriptor to rceeive -events for and events is either C, C or C to receive the given events. - -Please note that most of the more scalable backend mechanisms (for example -epoll and solaris ports) can result in spurious readyness notifications -for file descriptors, so you practically need to use non-blocking I/O (and -treat callback invocation as hint only), or retest separately with a safe -interface before doing I/O (XLib can do this), or force the use of either -C or C, which don't suffer from this -problem. Also note that it is quite easy to have your callback invoked -when the readyness condition is no longer valid even when employing -typical ways of handling events, so its a good idea to use non-blocking -I/O unconditionally. +Configures an C watcher. The C is the file descriptor to +rceeive events for and events is either C, C or +C to receive the given events. =back @@ -758,7 +765,7 @@ ev_loop (loop, 0); -=head2 C - relative and optionally recurring timeouts +=head2 C - relative and optionally repeating timeouts Timer watchers are simple relative timers that generate an event after a given time, and optionally repeating in regular intervals after that. @@ -850,7 +857,7 @@ ev_timer_again (&mytimer); -=head2 C - to cron or not to cron +=head2 C - to cron or not to cron? Periodic watchers are also timers of a kind, but they are very versatile (and unfortunately a bit complex). @@ -988,7 +995,7 @@ ev_periodic_start (loop, &hourly_tick); -=head2 C - signal me when a signal gets signalled +=head2 C - signal me when a signal gets signalled! Signal watchers will trigger an event when the process receives a specific signal one or more times. Even though signals are very asynchronous, libev @@ -1014,7 +1021,7 @@ =back -=head2 C - wait for pid status changes +=head2 C - watch out for process status changes Child watchers trigger when your process receives a SIGCHLD in response to some child status changes (most typically when a child of yours dies). @@ -1047,7 +1054,7 @@ ev_signal_start (loop, &sigint_cb); -=head2 C - when you've got nothing better to do +=head2 C - when you've got nothing better to do... Idle watchers trigger events when there are no other events are pending (prepare, check and other idle watchers do not count). That is, as long @@ -1091,7 +1098,7 @@ ev_idle_start (loop, idle_cb); -=head2 C and C - customise your event loop +=head2 C and C - customise your event loop! Prepare and check watchers are usually (but not always) used in tandem: prepare watchers get invoked before the process blocks and check watchers @@ -1135,7 +1142,7 @@ Example: *TODO*. -=head2 C - when one backend isn't enough +=head2 C - when one backend isn't enough... This is a rather advanced watcher type that lets you embed one event loop into another (currently only C events are supported in the embedded @@ -1464,14 +1471,14 @@ ev_win32.c required on win32 platforms only - ev_select.c only when select backend is enabled (which is is by default) + ev_select.c only when select backend is enabled (which is by default) ev_poll.c only when poll backend is enabled (disabled by default) ev_epoll.c only when the epoll backend is enabled (disabled by default) ev_kqueue.c only when the kqueue backend is enabled (disabled by default) ev_port.c only when the solaris port backend is enabled (disabled by default) F includes the backend files directly when enabled, so you only need -to compile a single file. +to compile this single file. =head3 LIBEVENT COMPATIBILITY API @@ -1494,8 +1501,8 @@ Instead of using C and providing your config in whatever way you want, you can also C in your -F and leave C off. F will then include -F and configure itself accordingly. +F and leave C undefined. F will then +include F and configure itself accordingly. For this of course you need the m4 file: @@ -1585,7 +1592,7 @@ supports some types of fds correctly (the only platform we found that supports ptys for example was NetBSD), so kqueue might be compiled in, but not be used unless explicitly requested. The best way to use it is to find -out wether kqueue supports your type of fd properly and use an embedded +out whether kqueue supports your type of fd properly and use an embedded kqueue loop. =item EV_USE_PORT