| … | |
… | |
| 7 | |
7 | |
| 8 | All |
8 | All |
| 9 | |
9 | |
| 10 | --enable-everything |
10 | --enable-everything |
| 11 | Add (or remove) support for all non-multichoice options listed in |
11 | Add (or remove) support for all non-multichoice options listed in |
| 12 | "./configure --help". |
12 | "./configure --help", except for "--enable-assert". |
| 13 | |
13 | |
| 14 | You can specify this and then disable options you do not like by |
14 | You can specify this and then disable options you do not like by |
| 15 | *following* this with the appropriate "--disable-..." arguments, or |
15 | *following* this with the appropriate "--disable-..." arguments, or |
| 16 | you can start with a minimal configuration by specifying |
16 | you can start with a minimal configuration by specifying |
| 17 | "--disable-everything" and than adding just the "--enable-..." |
17 | "--disable-everything" and than adding just the "--enable-..." |
| … | |
… | |
| 169 | settable extra linespacing /-lsp) |
169 | settable extra linespacing /-lsp) |
| 170 | iso-14755 5.1 (basic) support |
170 | iso-14755 5.1 (basic) support |
| 171 | tripleclickwords (-tcw) |
171 | tripleclickwords (-tcw) |
| 172 | settable insecure mode (-insecure) |
172 | settable insecure mode (-insecure) |
| 173 | keysym remapping support |
173 | keysym remapping support |
| 174 | cursor blinking and underline cursor (-cb, -uc) |
174 | cursor blinking and underline cursor (-bc, -uc) |
| 175 | XEmbed support (-embed) |
175 | XEmbed support (-embed) |
| 176 | user-pty (-pty-fd) |
176 | user-pty (-pty-fd) |
| 177 | hold on exit (-hold) |
177 | hold on exit (-hold) |
| 178 | compile in built-in block graphics |
178 | compile in built-in block graphics |
| 179 | skip builtin block graphics (-sbg) |
179 | skip builtin block graphics (-sbg) |
| … | |
… | |
| 234 | running configure. Even when compiled in, perl will *not* be |
234 | running configure. Even when compiled in, perl will *not* be |
| 235 | initialised when all extensions have been disabled "-pe "" |
235 | initialised when all extensions have been disabled "-pe "" |
| 236 | --perl-ext-common """, so it should be safe to enable from a |
236 | --perl-ext-common """, so it should be safe to enable from a |
| 237 | resource standpoint. |
237 | resource standpoint. |
| 238 | |
238 | |
|
|
239 | --enable-assert (default: off) |
|
|
240 | Enables the assertions in the code, normally disabled. This switch |
|
|
241 | is only useful when developing rxvt-unicode. |
|
|
242 | |
| 239 | --with-afterimage-config=DIR |
243 | --with-afterimage-config=DIR |
| 240 | Look for the libAfterImage config script in DIR. |
244 | Look for the libAfterImage config script in DIR. |
| 241 | |
245 | |
| 242 | --with-name=NAME (default: urxvt) |
246 | --with-name=NAME (default: urxvt) |
| 243 | Set the basename for the installed binaries, resulting in "urxvt", |
247 | Set the basename for the installed binaries, resulting in "urxvt", |
